CATEGORY: FLOOR
OZ-AK Soil Testing Equipments are used to understand and examine physical / mechanical properties, critical characteristic behaviors, performance of soil, mixtures with and without binders during compaction process, shear or internal fluid flow under dynamic and vibrating loading conditions. Soil characteristics are important in determining the most appropriate method for digging underground tunnels.
All man-made structures need a foundation that can withstand live, constant and wind loads. Soil testing allows engineering firms and construction companies to predict the mechanical behavior of soils and provide a safe environment for people in or around structures, and to design foundations that are resistant to potential forces, including unusual and extreme events such as earthquakes and hurricanes.
DIRECT CUTTING TESTER DIGITAL
STANDARDS: TS 1900-2, ASTM D3080, BS 1377-7, AASHTO T236, NF P094 071-1 / 2
The device is capable of performing standard and permanent cutting stages and consolidation with fully automatic control. The system consists of a microstep control unit for applying horizontal and vertical loads to soil samples.
The system is capable of performing a consolidation phase automatically in 32 stages. Horizontal shear makes deformation at specified rate or load change at specified rate, or fixed load steps at specified times. The system is capable of displaying the actual status of the test and the graphical appearance on the screen in real time. The system is capable of changing the operator's test operations and controlling the stages of the test.
CAPACITY: 2.5, 5 or 10 kN
VERTICAL MOTOR Stepper motor
HORIZONTAL MOTOR Stepper motor
SPEED RANGE: 0.0001 to 10 mm / min.
HORIZONTAL MOTION: 12.5 mm
VERTICAL MOTION: 12.5 mm
Power: 220-240 V 1ph 50/60 Hz 250 W
Size: 228 x 560 x 762 mm
Weight: 63 Kg
DIRECT CUTTING TESTER DIGITAL
STANDARDS: TS 1900-2, ASTM D3080, BS 1377-7, AASHTO T236, NF P094 071-1 / 2
The device is capable of performing standard and permanent cutting stages and consolidation with fully automatic control. The system consists of a microstep control unit for applying horizontal and vertical loads to soil samples.
The system is capable of performing a consolidation phase automatically in 32 stages. Horizontal shear makes deformation at specified rate or load change at specified rate, or fixed load steps at specified times. The system is capable of displaying the actual status of the test and the graphical appearance on the screen in real time. The system is capable of changing the operator's test operations and controlling the stages of the test.
CAPACITY: 2.5, 5 or 10 kN
VERTICAL MOTOR Stepper motor
HORIZONTAL MOTOR Stepper motor
SPEED RANGE: 0.0001 to 10 mm / min.
HORIZONTAL MOTION: 12.5 mm
VERTICAL MOTION: 12.5 mm
Power: 220-240 V 1ph 50/60 Hz 250 W
Size: 228 x 560 x 762 mm
Weight: 63 Kg
CBR STABILITY TESTER 50 KN CAPACITY
STANDARDS: TS 1900-2, ASTM D1883, D3668, BS 1377-4,1924, AASTHO T193
The instrument frame is made of durable material for load and deformation measurement. Designed for use with minimal maintenance. Plate rising speeds are 1.27-1 mm / min. Motor protected against overload. The applied load is measured by a precision load cell with a capacity of 50 kN and displayed on the digital display. Max movement and mold are controlled by safety switch. The device is complete with load cell, displacement transducer, penetration piston.
Max. Vertical clearance: 645 mm
Horizontal clearance: 275 mm.
Cylinder movement: 60 mm.
Power: 20-240 V 1 ph 50 Hz 750 W
Size: 520 x 550 x 1450 (h) mm.
Weight: 155 Kg
CBR DEVICE LAND TYPE 50 KN CAPACITY
The applied load is delivered through the mechanical jack and impellers.
Top beam adjustable.
The device is supplied with a 50 kN load ring penetration piston, dial gauge and load conversion table.
The device can be used to perform CBR testing on site.
Dimensions: 430 x 380 x 1180 mm
Weight: 80 kg
PLATE LOADING TEST EQUIPMENT
STANDARDS: CNR N ° 146, Method “B” - BS 1377: 9
Hydraulic jack with a capacity of 100-200-500 kN.
Pressure manometer 500 kn capacity with 0,2 kn precision
Carrying Case
Weight: 110 kg
THREE AXIS TESTER 50 KN CAPACITY
STANDARDS: BS-1377: 7 and 8, ASTM D-2850
The device has been developed to meet all requirements in soil laboratories.
The device is very simple to use; The test feed rate can be easily adjusted by means of a microprocessor with the self-learning touch screen and keyboard and the operating manual inside.
Infinite stability is thus given in real time.
Machine position safety is composed of upper and lower limit switch.
4 channel cell
The device has the ability to work with and without a computer.
Has the ability to report.
Has the ability to draw graphics.
Data can be displayed in Excell format upon request.
Loadcell
Cell
Touch control screen
Load capacity: 50kN
Operating speed range: 0,00001-9,99999 mm / min
Speed loading feature: 25 mm / min
Deformation measurement: LVDT
Lateral pressure transducer: 24-bit analog readout
Vertical pressure transducer: 24-bit analog readout
Loadcell: 24 bit analog readout
LDVT: 24-bit analog readout
Porous discs, top and bottom heads
Water tank and connection apparatus
Sample preparation apparatus
Membrane insertion apparatus
Vertical daylight: 0-790 mm. (0-530 mm. With Ring)
Distance between columns: 360 mm
Base diameter: 158 mm
Power supply: 220-240 V 1 phase 50 Hz 750 W
Weight: 105 Kg
AUTOMATIC EARTH COMPACTOR
STANDARDS: TS 1900-1, BS 1377,1924, ASTM D558, D560, D698, D1557, AASTHO T99, T134, T136, T180
The device provides compression in a predetermined stroke pattern. Solid state is checked for durability and continuity. The automatic digital counter sets the number of strokes of the reset and test.
Adjustable ram fall height 0-450 mm.
The knob weight can be adjusted from 2.5 to 4.5 kg.
By setting the pressure, the number of strokes is adjusted to each layer.
Rammer: BS circular rim, 50 mm diameter, rammer adjustable in weight of 2.5 kg or 4.5 kg. The rammer can be adjusted to 2 inches (50.8 mm) diameter, 5.5 lb (2.5 kg) or 10 lb (4.5 kg) with ASTM circular surface.
Drop height: BS 300 mm or 450 mm adjustable. ASTM can be set to 12 inches (305 mm) or 18 inches (457 mm)
Size: 450x600 x 1680 mm.
Weight: 180 Kg
LIQUID LIMIT CONICAL PENETROMETER
STANDARDS: TS 1900-1, BS 1377-2
The device has a free fall mechanism over time.
Power: 220-240 V 1ph 50 Hz
Size: 220x170x410 mm.
Weight: 9 Kg
Proctor penetrometer
Standards: ASTM D 1558
It is used to determine the relationship between fine-grained soils and moisture penetration resistance in an area.
Penetrometer with 9 interchangeable stainless steel pins (4,52-5,23-6,40-9,07-12,83-16,54-20,22-24,79-28,55 mm) and carrying case .
Weight: 8 kg
SAND DISCOVERY SET
STANDARDS: BS 1377: 9; BS 1924: 2
Sand Concentration Test Set is used for density and moisture determination tests.
Suitable for use in off-road conditions.
Different models are available, plastic (ASTM standard) and metal (EN standard).
Sand Concentrate Set 100 mm
Sand Concentration Set 150 mm
Sand Concentration Set 200 mm
SAND CONE TEST SET
STANDARDS: ASTM D1556, AASTHO T191
Sand cone test set is used to determine the density and moisture determination of fine grained compacted soil in situ.
The set consists of the following products;
Steel double metal cone with valve,
Plastic sand cone can (5 lt capacity),
Consists of perforated metal tray.
Weight: 5 Kg
SOIL SAMPLER
STANDARDS: TS 1900-1, ASTM D2937, BS 1377/9
The soil sampler is used for sampling from the compacted fill or undisturbed soil and evaluating the density of the compacted sample.
The device consists of a sliding rod, free fall hammer (10 kg), head and sample receiver (diameter: 100 mm). It is galvanized against corrosion.
Weight: 15 KG
Consolidation Test Device
STANDARDS: TS 1900-2, ASTM D2435, D3877, D4546 / BS 1377: 5 AASHTO T216 / NF P94 090-1, P094 091
The device is made of strong cast aluminum frame for high precision under load. The load bridge assemblies are of high precision self-aligning toggle housing.
The beam provides three loading ratios of 9: 1, 10: 1 and 11: 1 and the desired amount of weight can be suspended in the beam section. The maximum load of the slots is 150 kg. The oedometer can use up to 100 cm2 cells.
Konsolidayon cell, weights, dial gauge, table should be ordered separately.
Weight: 23 Kg
VIBRATING MALLET EXPERIMENT SET
Standards: ASTM D 7382-08
These test methods include determining the maximum dry unit weight and water capacity range for effective compaction of granular soil.
The vibratory rammer is used to apply overload and compressive force to the soil sample.
Stand with vibrating mallet and mold.
Dimensions: 270 x 400 x 1160 (h) mm
DENSITY AND WATER CONTENT DETERMINATION (PROTECTOR TEST SET)
STANDARDS: TS 1900-1, EN 13286-2, ASTM D558, D559, D560, D698, D1557, AASTHO T99, T134, T135, T136, T180, BS 1377-4, 1924-2, NF P94-093, P94- 078, DIN18127
LIQUID LIMIT (CASAGRANDE) TESTER (MANUAL)
STANDARDS: TS 1900-1, ASTM D 4318, AASHTO T 89, BS 1377
The Casagrande tester is used to determine the water content of the instrument by placing the ground sample of a plastic consistency on the bowl of the device, and closing the slit (notch) formed with the special spoon on the sample by lowering the bowl.
The device comes with an ebonite base and a plug-in brass container.
The fall height of the container can be adjusted by the impact mechanism.
The device has a tour counter. (multiplication counter)
The grooving knife must be ordered separately.
Size: 150 x 150 x 120 (h) mm.
Weight: 3 Kg
PLASTIC LIMIT TEST SET
Standards: ASTM D4318 / AASHTO T90 / BS 1377: 2 / UNI 10014 / UNE 103-104 / NF P94-051
Plastic Limit Test Set; It is used to determine the lowest moisture content of soil samples.
Set Contents:
Frosted Glass Plate / 300 x 300 x 10 mm
Porcelain Capsule / Diameter: 120 mm
Flexible Spatula / 100 mm
Aluminum Moisture Container / Diameter: 55 x 35 mm (6 pieces)
Weight: 5 kg
-PLASTIC LIMIT EXPERIMENT-
A sample is prepared for the liquid limit. This material is put into the container and mixed with distilled water so that it does not adhere when it is kneaded with the fingers, but can be easily rounded. This material is given an ellipsoidal shape by hand and placed on a flat plate. When the diameter of the rods is 3 mm, the material is collected and kneaded again into a pellet.
This kneading process is continued until the 3 mm diameter bar is cracked and divided into several pieces. The water content of the pieces of this crumbled bar is determined. These water content averages give the plastic limit value of the ground.
PLASTIC LIMIT TEST SET
Standards: ASTM D4318 / AASHTO T90 / BS 1377: 2 / UNI 10014 / UNE 103-104 / NF P94-051
Plastic Limit Test Set; It is used to determine the lowest moisture content of soil samples.
Set Contents:
Frosted Glass Plate / 300 x 300 x 10 mm
Porcelain Capsule / Diameter: 120 mm
Flexible Spatula / 100 mm
Aluminum Moisture Container / Diameter: 55 x 35 mm (6 pieces)
Weight: 5 kg
-PLASTIC LIMIT EXPERIMENT-
A sample is prepared for the liquid limit. This material is put into the container and mixed with distilled water so that it does not adhere when it is kneaded with the fingers, but can be easily rounded. This material is given an ellipsoidal shape by hand and placed on a flat plate. When the diameter of the rods is 3 mm, the material is collected and kneaded again into a pellet.
This kneading process is continued until the 3 mm diameter bar is cracked and divided into several pieces. The water content of the pieces of this crumbled bar is determined. These water content averages give the plastic limit value of the ground.
CONFLICT LIMIT TESTER
STANDARDS: TS 1900-1, BS 1377-2, ASTM D427, AASTHO T92
This tester is used to determine the maximum water content in the absence of shrinkage of the samples after drying the soil samples.
The set consists of the following parts:
Shrink cup, diameter 45 x 12.7 mm (2 pieces)
Crystallized container diameter 57x32 mm
Shrinkage prong plate, three metal spikes made of fiberglass
Glass mist container, diameter. 120 mm horizontal base
Measure 25 ml. capacity
Flexible spatula, 100 mm. bladed
NEEDLE HOLE TESTER
Standards: TS 1900-2: 2006 / T1: 2007, ASTM D 4647
Some soils that tend to disperse spontaneously in water are considered “suspicious soils er in terms of erosion and piping. These soils are known as bilim dispersive clay or dispersive soils inde in soil mechanics. These structurally unstable soils can be easily dispersed and highly eroded. If dispersive clay soils are used in the construction of water structures, fill dams and road fillings, they should be well defined and constructed using appropriate techniques. Otherwise, we face serious engineering problems that end up in the collapses. Erosion due to dispersibility of clay; The mineralogy of the clay depends on its chemical structure and the nature and quantity of dissolved salt content in the ground cavities and water causing erosion.
This test technique allows simple classification of soil samples and determination of soil quality.
The pinhole tester is used to determine the tendency to wear of the floor with water flow.
MARSH HOPPER SET
Standards: ISO 2431
It is used in viscosity determination of liquid substances.
Mouth opening: 4.7 mm
Screen Size: 2 mm
Weight: 1 kg
CBR INFLATION TEST SET
Set in general:
Inflatable plate,
Inflatable three pillars,
Dial gauge (10 mm capacity): 0.01 mm precision
Inflatable pool is optional.
CBR MOLD SET
STANDARDS: ASTM D1883, AASHTO T193, BS 1377, 1924
The set consists of the following parts
PERFORATED BOTTOM TRAY,
BOTTOM WITHOUT HOLE,
BODY, COLLAR, CUTTING SIDE,
2,27 KG PERFORATED, 2,27KG SLIDED SURPRISE WEIGHT AND VACCITY DISC.
COMPLETELY COATED TO ANTI-RUST ELECTROLYSIS.